Cable Trays
Perforated and solid steel cable trays from CASK STEEL in light, medium and heavy duty, with every bend, tee, cross, reducer and cover of the same size. Made at our factory in Dilovası, Kocaeli, in accordance with IEC 61537.
What a cable tray is
A cable tray is a continuous steel base with two side walls that carries power, control and data cables along walls, ceilings and structures. The perforated base lets heat escape from the cables and gives many fixing points; the solid base gives the cables full protection from below.
Every tray is formed from prime-quality steel sheet and comes with matching fittings and covers, so a complete tray route can be ordered from one catalogue, under one part-number system.
Types of cable tray
Eight straight-section types. Every type has its own base number; the size and finish follow it.
| Type | Base number | Width W (mm) | Side height H (mm) | Sheet thickness T (mm) |
|---|---|---|---|---|
| Perforated, light duty | CST-CT056 | 50 to 900 | 15, 25, 40 | 1.0 to 1.5 |
| Perforated, medium duty | CST-CT066 | 50 to 900 | 25 | 1.0 to 1.5 |
| Perforated, heavy duty | CST-CT004 | 50 to 900 | 40 to 150 | 1.0 to 2.0 |
| Perforated, reinforced, heavy duty | CST-CT087 | 100 to 900 | 60, 75, 100 | 1.0 to 1.5 |
| Perforated, with clamping lid | CST-CT097 | 100 to 900 | 50, 75, 100 | 1.0 to 2.0 |
| Solid, light duty | CST-CT120 | 50 to 900 | 15, 25, 40 | 1.0 to 1.5 |
| Solid, medium duty | CST-CT121 | 50 to 900 | 25 | 1.0 to 1.5 |
| Solid, heavy duty | CST-CT007 | 50 to 900 | 50 to 100 | 1.0 to 2.5 |
Standard length 3,000 mm; selected sizes are also made in 2,500 mm. The catalogue shows, for each type, which thicknesses are made in each width and side height. Other sizes are made to order.
Fittings and covers
Fittings are made in the same widths, side heights and thicknesses as the straight sections, in the perforated, reinforced, turned-in edge (KT3 profile) and clamping-lid versions.
Horizontal fittings
45° and 90° flat bends, tees, crosses, and straight, left and right reducers. Bend radius from 50 to 900 mm, depending on the type.
Vertical fittings
90° vertical inside and outside bends, flexible inside and outside bends, and an adjustable vertical riser (CST-CT124).
Covers
Flat (CST-CT041), ventilated (CST-CT047) and peaked (CST-CT044) covers, and flat covers for bends, tees, crosses, reducers and vertical bends.
Materials and finishes
Hot-dip galvanized is the standard finish; every type is available in all finishes. The finish code is the last part of the part number.
| Code | Finish | Typical environment |
|---|---|---|
| -HDG | Hot-dip galvanized after fabrication, EN ISO 1461 (standard) | Outdoor and industrial, C4 |
| -PG | Pre-galvanized strip, EN 10346 (Z275) | Indoor and dry, C1 to C2 |
| -ZM | Zinc-aluminium-magnesium coated steel, EN 10346 | Severe outdoor and coastal, C4 to C5 |
| -EP | Hot-dip galvanized, then epoxy or polyester powder coated (RAL colour on request) | Coastal and chemical, C5 |
| -SS304 | Stainless steel AISI 304 | Food, pharma, indoor wet areas, C3 to C4 |
| -SS316 | Stainless steel AISI 316L | Marine, offshore and chemical plants, C5 |
| -AL | Aluminium, for selected trays | Indoor and outdoor, C3 |
Part numbers
Every CASK Steel part number describes the product: base number, width, side height, sheet thickness and finish. Where more than one bend radius is made, the radius follows the thickness; a 2,500 mm length is added before the finish.
- CST-CT004-300-100-1.5-HDG: perforated heavy-duty tray, W 300, H 100, T 1.5, hot-dip galvanized
- CST-CT056-120-25-1.0-HDG: perforated light-duty tray, W 120, H 25, T 1.0
- CST-CT007-120-75-1.2-HDG: solid heavy-duty tray, W 120, H 75, T 1.2
- CST-CT023-300-100-1.5-R300-HDG: 90° flat bend, heavy duty, radius 300 mm
- CST-CT004-100-50-2.0-L2500-HDG: the same tray in 2,500 mm length
All sizes, thickness tables and drawings are in the catalogue: download part 1, cable trays (PDF) · العربية (PDF).
Standards and quality
- Cable tray systems in accordance with IEC 61537, including loading capability and support span
- Hot-dip galvanizing to EN ISO 1461; pre-galvanized and zinc-magnesium strip to EN 10346
- Made in our factory under ISO 9001, ISO 14001 and ISO 45001
Photos






Frequently asked questions
Perforated or solid tray: which one do I need?
Perforated trays let heat escape and suit most power and control cables. Solid trays give full protection from below and suit cables that must be shielded, for example instrument and data cables.
What is the difference between light, medium and heavy duty?
The duty follows the sheet thickness and side height: light-duty trays (1.0 to 1.5 mm) carry smaller cable loads, heavy-duty trays (up to 2.0 mm, side height up to 150 mm) carry large power cables over longer support spans. Load tables are in the catalogue.
Which finish should I choose outdoors?
Hot-dip galvanized is the usual choice outdoors and in industrial plants. For coastal and severe sites choose zinc-magnesium, powder-coated or stainless steel AISI 316L.
Can you make sizes that are not in the catalogue?
Yes. Other sizes are made to order.
Related products
Questions about this product? Contact us
