Cable Trunking and Channels

CE, IEC 61537, ISO 1461

Enclosed steel cable trunking with its bends, tees and fittings, and C strut channels for support frames, from CASK STEEL. Made at our factory in Dilovası, Kocaeli, in accordance with IEC 61537.

What cable trunking is

Cable trunking is an enclosed steel section with a solid base and solid sides. It gives cables full protection from dust, damage and accidental contact, and is used mainly for instrumentation, control and communication cables.

Every trunking section and fitting is supplied with joint holes, so the parts of a route connect to each other directly.

Steel cable trunking packed on pallets at our factory

Cable trunking

ProductBase numberSizes
Cable trunking, straightCST-TK002W 50 to 300 mm, H 50 to 150 mm, T 1.2 to 2.0 mm
90° flat bendCST-TK004W 100 to 300 mm, H 50 and 100 mm
45° flat bendCST-TK003W 100 to 300 mm, H 100 mm
TeeCST-TK005W 100 to 300 mm, H 50 and 100 mm
Vertical teeCST-TK006W 100 to 300 mm, H 100 mm
CrossCST-TK011Made to order, radius 300 mm, W 100 to 750 mm
Reducers: straight, right, leftCST-TK012 to TK014Made to order, to suit the straight trunking widths
90° vertical inside and outside bendsCST-TK015, TK016Made to order, to suit the straight trunking widths

Lengths 2,500 and 3,000 mm. Sheet thickness 1.2 mm (light), 1.5 mm (medium) and 2.0 mm (heavy).

Strut channels

C strut channels carry cable trays, ladders and trunking on walls, ceilings and support frames. The continuous slot takes spring nuts and fixings at any point along the channel.

ProductBase numberSizes
C channel, singleCST-CH00419 sizes; W 41 to 128 mm, H up to 120 mm, T 1.5 to 10.0 mm
C channel, single, slottedCST-CH00731 sizes; W 41 mm, H 21 and 41 mm, T 2.0 to 5.0 mm

Standard length 3,000 mm; selected channels are also made in 2,500 mm.

Materials and finishes

Hot-dip galvanized is the standard finish; trunking and channels are also made in the other finishes below. The finish code is the last part of the part number.

CodeFinishTypical environment
-HDGHot-dip galvanized after fabrication, EN ISO 1461 (standard)Outdoor and industrial, C4
-PGPre-galvanized strip, EN 10346 (Z275)Indoor and dry, C1 to C2
-ZMZinc-aluminium-magnesium coated steel, EN 10346Severe outdoor and coastal, C4 to C5
-EPHot-dip galvanized, then epoxy or polyester powder coated (RAL colour on request)Coastal and chemical, C5
-SS304Stainless steel AISI 304Food, pharma, indoor wet areas, C3 to C4
-SS316Stainless steel AISI 316LMarine, offshore and chemical plants, C5

Part numbers

Every CASK Steel part number describes the product: base number, width, side height, sheet thickness and finish. Made-to-order fittings carry their base number and finish.

  • CST-TK002-200-100-1.5-HDG: cable trunking, W 200, H 100, T 1.5, hot-dip galvanized
  • CST-TK004-300-100-1.5-HDG: trunking 90° flat bend, W 300, H 100
  • CST-TK011-HDG: trunking cross, made to order
  • CST-CH007-41-41-2.5-HDG: slotted C channel, 41 x 41 mm, T 2.5

All sizes and drawings are in the catalogue: download part 3, trunking and channels (PDF) · العربية (PDF).

Standards and quality

  • Cable management systems in accordance with IEC 61537
  • Hot-dip galvanizing to EN ISO 1461; pre-galvanized and zinc-magnesium strip to EN 10346
  • Made in our factory under ISO 9001, ISO 14001 and ISO 45001

Frequently asked questions

Trunking or solid cable tray: what is the difference?

Both have a solid base. Trunking is an enclosed system with its own fittings and joint holes, for cables that need full protection; a solid tray is an open tray that can take a cover.

Do you make trunking fittings that are not in the tables?

Yes. Crosses, reducers and vertical bends are made to order to suit the straight trunking widths.

What are strut channels used for?

They form the support frames that carry trays, ladders and trunking. The continuous slot takes spring nuts and fixings anywhere along the channel.

Questions about this product? Contact us